資料介紹

Table of Contents
EVAL-CN0395-ARDZ Shield
The circuit below is an arduino compatible, single supply 16-bit volatile organic compound detector using a metal oxide sensor. It uses ADN8810 to precisely control the current running through the sensor to get to within the 1% voltage accuracy needed for the heating element of the sensor.
CN0395 measures indoor air quality by utilizing a Metal Oxide Sensor to detect gases composed of volatile organic compounds. The sensor is composed of a heating resistor and a sensing resistor. When the sense resistor is heated its value changes as a function of the concentrations of different gasses.
Connectors and Jumper Configurations
Headers
P1
The current output DAC, ADN8810, has an output voltage compliance that needs to be met to maintain a linear current output. This can be done by putting a jumper on position 2 and 3 which attaches the ENCOMP pin of the part to ground for output voltages up to 2V.
For higher output voltages that 2V, tie the ENCOMP pin to +5V to maintain the output stability of the part.
P2
P2 header selects the current path from the current output DAC, ADN8810. It is populated across RH+ by default.
Silkscreen | Current Path | Pins |
---|---|---|
RCAL1 | 71.5Ω | 1 & 2 |
RCAL1 | 10.0Ω | 3 & 4 |
RH+ | Heating Resistor | 5 & 6 |
Sensor
CN0395 has the TGS8100 on board as default. Using a different set of sensors require a recalculation and replacement of the sense resistors that sets the full scale current for the device. Provision for alphasense sensors or with similar footprint is available and a screw terminal is also in place for any other types of sensors.
Recommended Sensors
If you are using a different sensor, you will need to wire in the appropriate signals into the board via the screw terminal (P8). This also means that you will have to remove the TGS8100 sensor that comes on the board by default. Below is a table of how to use P8 to input other sensors.
P8
Silkscreen Name | Pin Number | Description |
---|---|---|
RH+ | Pin 1 | Postive Pin of Heating Resistor |
AGND | Pin 2 | Negative Pin of Heating Resistor |
RS+ | Pin 3 | Postive Pin of Sensing Resistor |
AGND | Pin 4 | Negative Pin of Sensing Resistor |
Spacers
Spacers that could cater various surface mount and through hole packages are available on the board to make some modifications on the board easier.
Resistor spacers, R17_SPACER and R19_SPACER, are used to hold the sense resistors to select the maximum output current of the ADN8810. Changing these maximum output current of the ADN8810 allows the board to cater multiple types of sensor that use up to 300mA of current for measurements.
Sense resistors (RSN) can be calculated by using the formula below:
RSN= 4.096/(10* Full Scale Current)
Button
Pressing push button S2 allows the user to do a hard reset of the temperature and humidity sensor SHT30.
Schematic, PCB Layout, Bill of Materials
EVAL-CN0395-ARDZ Design & Integration Files
- Schematics
- PCB Layout
- Bill of Materials
- Allegro Project
Software
End of Document
- 基于CN-0395流量表的
- CN0395設計與集成文件
- UG-1656:將EVAL-ADT7420ARDZ屏蔽與Arduino或Lduino硬件配合使用
- EVAL-CN0338-ARDZ屏蔽
- EVAL-CN0391-ARDZ屏蔽
- EVAL-CN0394-ARDZ屏蔽
- EVAL-CN0397-ARDZ屏蔽
- EVAL-CN0398-ARDZ屏蔽概述
- EVL-CN0357 ARDZ設計與集成文件
- EVL-CN0216 ARDZ設計與集成文件
- EVAL-AD8302-ARDZ-評估軟件
- CN0395 Design & Integration Files
- EVAL-ADT7420ARDZ - Schematic
- EVAL-AD8302-ARDZ - Evaluation Software
- 基于EVAL-CN0357-ARDZ流量表的參考設計
- PI電磁屏蔽材料的屏蔽機理和影響因素 2643次閱讀
- 線纜屏蔽材料的種類及應用 1248次閱讀
- 屏蔽線為什么使用雙絞線 屏蔽線應該怎樣接地 1w次閱讀
- 屏蔽雙絞線和非屏蔽雙絞線的主要差異是什么 1.4w次閱讀
- 各種屏蔽體的屏蔽效能計算方法解析 2.6w次閱讀
- 如何計算屏蔽體的屏蔽效能 7224次閱讀
- 屏蔽罩常用于哪些電路? 8775次閱讀
- 什么是屏蔽線_屏蔽線的類型_屏蔽線的作用 2w次閱讀
- 屏蔽線和非屏蔽線的區別_網線屏蔽線和非屏蔽線的區別 5.6w次閱讀
- 屏蔽水晶頭和非屏蔽的區別 6.1w次閱讀
- 屏蔽線纜在EMC屏蔽方面的參數特性 2.8w次閱讀
- 關于電磁場的屏蔽問題,如何屏蔽 2.2w次閱讀
- 電磁屏蔽的基本原則 6535次閱讀
- 非屏蔽雙絞線和屏蔽雙絞線有什么區別 4.6w次閱讀
- 靜電屏蔽、靜磁屏蔽和高頻電磁場屏蔽知識 1w次閱讀
下載排行
本周
- 1AN-1267: 使用ADSP-CM408F ADC控制器的電機控制反饋采樣時序
- 1.41MB | 3次下載 | 免費
- 2AN158 GD32VW553 Wi-Fi開發指南
- 1.51MB | 2次下載 | 免費
- 3AN148 GD32VW553射頻硬件開發指南
- 2.07MB | 1次下載 | 免費
- 4AN-1154: 采用恒定負滲漏電流優化ADF4157和ADF4158 PLL的相位噪聲和雜散性能
- 199.28KB | 次下載 | 免費
- 5AN-960: RS-485/RS-422電路實施指南
- 380.8KB | 次下載 | 免費
- 6EE-249:使用VisualDSP在A(yíng)DSP-218x DSP上實現軟件疊加
- 60.02KB | 次下載 | 免費
- 7AN-1111: 使用ADuCM360/ADuCM361時的降低功耗選項
- 306.09KB | 次下載 | 免費
- 8AN-904: ADuC7028評估板參考指南
- 815.82KB | 次下載 | 免費
本月
- 1ADI高性能電源管理解決方案
- 2.43 MB | 450次下載 | 免費
- 2免費開源CC3D飛控資料(電路圖&PCB源文件、BOM、
- 5.67 MB | 138次下載 | 1 積分
- 3基于STM32單片機智能手環心率計步器體溫顯示設計
- 0.10 MB | 130次下載 | 免費
- 4使用單片機實現七人表決器的程序和仿真資料免費下載
- 2.96 MB | 44次下載 | 免費
- 5美的電磁爐維修手冊大全
- 1.56 MB | 24次下載 | 5 積分
- 6如何正確測試電源的紋波
- 0.36 MB | 18次下載 | 免費
- 7感應筆電路圖
- 0.06 MB | 10次下載 | 免費
- 8萬用表UT58A原理圖
- 0.09 MB | 9次下載 | 5 積分
總榜
- 1matlab軟件下載入口
- 未知 | 935121次下載 | 10 積分
- 2開源硬件-PMP21529.1-4 開關降壓/升壓雙向直流/直流轉換器 PCB layout 設計
- 1.48MB | 420062次下載 | 10 積分
- 3Altium DXP2002下載入口
- 未知 | 233088次下載 | 10 積分
- 4電路仿真軟件multisim 10.0免費下載
- 340992 | 191367次下載 | 10 積分
- 5十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183335次下載 | 10 積分
- 6labview8.5下載
- 未知 | 81581次下載 | 10 積分
- 7Keil工具M(jìn)DK-Arm免費下載
- 0.02 MB | 73810次下載 | 10 積分
- 8LabVIEW 8.6下載
- 未知 | 65988次下載 | 10 積分
評論