MAX712電池充電器,max712 battery charger
MAX712電池充電器,max712 battery charger
關鍵字：MAX712電池充電器
本文源自下面的連接：http://www.rason.org/Projects/gelcell/gelcell.htm
12 VOLT GEL CELL CHARGER
BY N1HFX
Recently, a fellow amateur was looking for a gel cell charger which would first charge at a fixed rate and then later switch to a trickle charge when the cell was fully charged. After reviewing several catalogs and web sites, the MAX712 IC was discovered. This IC meets all the requirements for almost any type of battery charging system. The circuit in Figure 1 was designed specifically for 12 volt gel cells.
When a discharged gel cell is connected, the charger goes into a fast charge mode at a fixed rate of 400 ma. After the chip detects the voltage leveling off or when 4 1/2 hours has elapsed. (which ever happens first.) the fast charge will stop. After the fast charge has ended, the IC goes into a trickle charge rate of about 50 ma. This trickle charge continues until 13.8 volts is reached which will stop all charging current since the cell is now fully charged. If the cell voltage should drop for any reason, either a fast charge or trickle charge (IC will detect what is needed) will start again.
When constructing this circuit, be sure to attach a small heat sink to Q1. Apply a DC (partially filtered) voltage of at least 15.3 volts. The voltage must never go below this level even under load conditions. Many of the DC wall transformers available will work just fine as long as they meet the minimum voltage requirement. The input voltage can be as high as 24 volts. If the input voltage must be in the 30 volt range, increase R1 to about 820 ohms.
The output voltage must be aligned prior to use. Disconnect the battery from the circuit and apply power. Connect a digital volt meter or other accurate volt meter to pin 2 (positive lead) and to pin 12 (negative lead). Adjust R7 until exactly 13.8 volts is read.
Because this circuit will not overcharge a gel cell, the battery can be connected indefinitely. This circuit is designed primarily as a 12 backup system and can be connected to the load provided the device to be powered only draws current during power line interruptions. Use a diode from the battery to load if needed. This circuit makes an excellent battery backup to an amateur transceiver.
The MAX712 IC and the .62 ohm resistor are available from Digi-Key, 701 Brooks Ave, Thief River Falls, MN 56701 (1-800-344-4539). Order part numbers MAX712CPE-ND and 0.62W-1-ND respectively. All other parts are available at Radio Shack.
DE N1HFX
元件清單 PARTS LIST
| C1
聲明：本文內容及配圖由入駐作者撰寫或者入駐合作網站授權轉載。文章觀點僅代表作者本人，不代表電子發燒友網立場。文章及其配圖僅供工程師學習之用，如有內容侵權或者其他違規問題，請聯系本站處理。
舉報投訴
發布評論請先 登錄 相關推薦
熱點推薦
BQ25185線性電池充電器IC技術解析與應用指南Texas Instruments BQ25185線性電池充電器IC是一款單節、1A獨立線性電池充電器，具有電源路徑和太陽能輸入支持。該線性充電器
采用電源路徑電池充電器優化應用要想設計最佳電池充電集成電路 (IC) 以最大限度延長電池壽命并實現最佳系統性能，可能充滿挑戰。是選擇電源路徑電池充電器還是非電源路徑
Analog Devices / Maxim Integrated MAX77301鋰離子線性電池充電器數據手冊Analog Devices MAX77301鋰離子線性電池充電器符合JEITA標準，可通過USB端口、專用充電器或通用適配器工作。該IC通過USB主機或集線器提供自動適配器類型檢測和
Analog Devices / Maxim Integrated MAX77840 3.15A開關模式充電器數據手冊Analog Devices MAX77840 3.15A開關模式充電器包括一個ModelGauge? m5電量計，集成了用于鋰離子電池的USB BC1.2檢測功能和一個SAFEOUT LDO。該
Analog Devices / Maxim Integrated MAX77985/MAX77986單節鋰離子電池充電器數據手冊Analog Devices MAX77985/MAX77986單節鋰離子電池充電器通過快速充電和Smart Power Selector?
Analog Devices / Maxim Integrated MAX77785/MAX77786單節鋰離子電池充電器數據手冊Analog Devices MAX77785/MAX77786單節鋰離子電池充電器是高性能高輸入3.5/5.5A快速充電器，采用Smart
Analog Devices Inc. MAX77972 FET充電器數據手冊Analog Devices Inc. MAX77972 FET充電器是一款獨立的AccuCharge?降壓充電器，可在13.7V輸入電壓和高達16V保護下工作。這款FET充電器支持高
Analog Devices Inc. MAX17335充電器/電量計/保護器IC數據手冊Analog Devices Inc. MAX17335 AccuCharge + ModelGauge? m5 EZ單節充電器/電量計/保護器IC是一款35μA IQ獨立充電器、電量計、保護器
芯伯樂XBLW GT712選型及應用設計指南在電子工程領域，精準的電流測量對于眾多電路設計與系統監控至關重要。芯伯樂推出的XBLWGT712電流傳感器以其獨特的優勢，成為工程師在諸多應用中的首選工具本文將深入剖析XBLWGT712的工作原理
dsPIC33CH1024MP712系列數據手冊電子發燒友網站提供《dsPIC33CH1024MP712系列數據手冊.pdf》資料免費下載
發表于 01-22 16:16
?0次下載
鋰電池充電器和鉛酸電池充電器怎么區分？有和不同？鋰電池充電器和鉛酸電池充電器怎么區分？有和不同？說起鉛酸電池充電器，我們首先想到的應用就是電動自
發表于 01-15 10:06
電池測試儀與充電器的區別 電池測試儀常見故障及解決方法電池測試儀和充電器是兩種不同的設備，它們在功能和用途上有明顯的區別。 電池測試儀與充電器的區別 電池測試儀： 功能 ：
車載電池充電器全解析整體思路是圍繞車載電池充電器展開，從其重要性、類型、選擇方法和使用注意事項等方面進行全面介紹，為讀者提供關于車載電池充電器的詳細信息和指導
手機筆記本電腦電池和充電器 UL認證如何辦理筆記本電腦更換電池
（可充電鋰離子或鋰聚合物電池，用于安裝到筆記本。
筆記本電腦充電器/電源適配器
（用于從交流墻上插座供電的外部充電器或適
發表于 10-30 09:02
版權所有 ? 湖南華秋數字科技有限公司 長沙市望城經濟技術開發區航空路6號手機智能終端產業園2號廠房3層（0731-88081133） 電子發燒友 （電路圖） 湘公網安備43011202000918 工商網監
湘ICP備2023018690號-1
|
評論