電子發燒友App
創作
發文章
發帖 
提問 
發資料
發視頻AD7156-適用于單片機平臺的無操作系統驅動程序
資料介紹
Table of Contents
AD7156 - No-OS Driver for Microchip Microcontroller Platforms
Supported Devices
Evaluation Boards
Overview
The AD7156 delivers a complete signal processing solution for capacitive sensors, featuring an ultralow power converter with fast response time.
The AD7156 uses an Analog Devices, Inc., capacitance-to-digital converter (CDC) technology, which combines features important for interfacing to real sensors, such as high input sensitivity and high tolerance of both input parasitic ground capacitance and leakage current.
The integrated adaptive threshold algorithm compensates for any variations in the sensor capacitance due to environmental factors like humidity and temperature or due to changes in the dielectric material over time.
By default, the AD7156 operates in standalone mode using the fixed power-up settings and indicates detection on two digital outputs. Alternatively, the AD7156 can be interfaced to a micro-controller via the serial interface, the internal registers can be programmed with user-defined settings, and the data and status can be read from the part.
The AD7156 operates with a 1.8 V to 3.6 V power supply. It is specified over the temperature range of ?40°C to +85°C.
Applications
- Buttons and switches
- Proximity sensing
- Contactless switching
- Position detection
- Level detection
- Portable products
The goal of this project (Microcontroller No-OS) is to be able to provide reference projects for lower end processors, which can't run Linux, or aren't running a specific operating system, to help those customers using microcontrollers with ADI parts. Here you can find a generic driver which can be used as a base for any microcontroller platform and also specific drivers for different microcontroller platforms.
Driver Description
The driver contains two parts:
- The driver for the AD7156 part, which may be used, without modifications, with any microcontroller.
- The Communication Driver, where the specific communication functions for the desired type of processor and communication protocol have to be implemented. This driver implements the communication with the device and hides the actual details of the communication protocol to the ADI driver. The Communication Driver has a standard interface, so the AD7156 driver can be used exactly as it is provided.
There are three functions which are called by the AD7156 driver:
- I2C_Init() – initializes the communication peripheral.
- I2C_Write() – writes data to the device.
- I2C_Read() – reads data from the device.
I2C driver architecture
The following functions are implemented in this version of AD7156 driver:
| Function | Description |
|---|---|
| void AD7156_GetRegisterValue(unsigned char* pReadData, unsigned char registerAddress, unsigned char bytesNumber) | Performs a burst read of a specified number of registers. |
| void AD7156_SetRegisterValue(unsigned short registerValue, unsigned char registerAddress, unsigned char bytesNumber) | Writes data into one or two registers. |
| char AD7156_Init(void) | Initializes the communication peripheral and checks if the device is present. |
| void AD7156_Reset(void) | Resets the device. |
| void AD7156_SetPowerMode(unsigned char pwrMode) | Sets the converter mode of operation. |
| void AD7156_ChannelState(unsigned char channel, unsigned char enableConv) | Enables or disables conversion on the selected channel. |
| void AD7156_SetRange(unsigned channel, unsigned char range) | Sets the input range of the specified channel. |
| float AD7156_GetRange(unsigned channel) | Reads the range bits from the device and returns the range in pF. |
| void AD7156_SetThresholdMode(unsigned char thrMode, unsigned char thrFixed) | Selects the threshold mode of operation. |
| void AD7156_SetThreshold(unsigned char channel, float pFthr) | Writes to the threshold register when threshold fixed mode is enabled. |
| void AD7156_SetSensitivity(unsigned char channel, float pFsensitivity) | Writes a value(pF) to the sensitivity register. This functions should be used when adaptive threshold mode is selected. |
| unsigned short AD7156_ReadChannelData(unsigned char channel) | Reads a 12-bit sample from the selected channel. |
| unsigned short AD7156_WaitReadChannelData(unsigned char channel) | Waits for a finished CDC conversion and reads a 12-bit sample from the selected channel. |
| float AD7156_ReadChannelCapacitance(unsigned char channel) | Reads a sample the selected channel and converts the data to picofarads(pF). |
| float AD7156_WaitReadChannelCapacitance(unsigned char channel) | Waits for a finished CDC conversion the selected channel, reads a sample and converts the data to picofarads(pF). |
HW Platform(s):
Downloads
- PmodCDC1 Demo for PIC32MX320F128H: https://github.com/analogdevicesinc/no-OS/tree/master/Microchip/PIC32MX320F128H/PmodCDC1
- PIC32MX320F128H Common Drivers: https://github.com/analogdevicesinc/no-OS/tree/master/Microchip/PIC32MX320F128H/Common
Digilent Cerebot MX3cK Quick Start Guide
This section contains a description of the steps required to run the AD7156 demonstration project on a Digilent Cerebot MX3cK platform.
Required Hardware
Required Software
- The AD7156 demonstration project for PIC32MX320F128H.
The AD7156 demonstration project for PIC32MX320F128H consists of three parts: the AD7156 Driver, the PmodCDC1 Demo for PIC32MX320F128H and the PIC32MX320F128H Common Drivers.
All three parts have to be downloaded.
Hardware Setup
A PmodCDC1 has to be connected to the J2 connector of Cerebot MX3cK development board.
Reference Project Overview
The following commands were implemented in this version of AD7156 reference project for Cerebot MX3cK board.
| Command | Description |
|---|---|
| help? | Displays all available commands. |
| channelRange? | Displays the set range for the selected channel. Accepted values: 1 - Displays the channel 1's range. 2 - Displays the channel 2's range. |
| channelRange= | Selects the range of the selected channel. Accepted values: channel: 1 - Select channel 1. 2 - Select channel 2. range: 0 - 0..2pF. 1 - 0..0.5pF 2 - 0..1pF 3 - 0..4pF. |
| powerMode? | Displays the current power mode. |
| powerMode= | Selects the power mode of the device. Accepted values: 0 - Idle. 1 - Continuous conversions. 2 - Single conversion. 3 - Power-down. |
| channelEnable= | Enables or disabled conversions on selected channel. Accepted values: channel: 1 - Select channel 1. 2 - Select channel 2. enable: 0 - Disable conversions on selected channel. 1 - Enable conversions on selected channel. |
| samples? | Reads 50 samples form the enabled channels and displays the data in pF. |
| buttons? | Checks if any of the two buttons are pressed or released. |
| reset! | Resets the device. |
Commands can be executed using a serial terminal connected to the UART1 peripheral of PIC32MX320F128H.
The following image shows a generic list of commands in a serial terminal connected to processor’s UART peripheral.
Software Project Setup
This section presents the steps for developing a software application that will run on the Digilent Cerebot MX3cK development board for controlling and monitoring the operation of the ADI part.
- Run the MPLAB X integrated development environment.
- Choose to create a new project.
- In the Choose Project window select Microchip Embedded category, Standalone Project and press Next.
- In the Select Device window choose PIC32MX320F128H device and press Next.
- In the Select Tool window select the desired hardware tool and press Next.
- In the Select Compiler window chose the XC32 compiler and press Next.
- In the Select Project Name and Folder window choose a name and a location for the project.
- After the project is created, all the downloaded source files have to be copied in the project folder and included in the project.
- The project is ready to be built and downloaded on the development board.
Digilent Cerebot MC7 Quick Start Guide
This section contains a description of the steps required to run the AD7156 demonstration project on a Digilent Cerebot MC7 platform.
Required Hardware
- PmodCDC1
Required Software
Hardware Setup
A PmodCDC1 can be connected to the J6 connector of Cerebot MC7 development board for I2C operation,
Reference Project Overview
Following commands were implemented in this version of AD7156 reference project for Cerebot MC7 board.
| Command | Description |
|---|---|
| help? | Displays all available commands. |
| range= | Selects the range of the channels. Accepted values: 0-3. |
| power= | Selects the power mode of the device. Accepted values: 0 - 3. |
| channel1= | Enables or disabled conversions on channel 1. Accepted values 0-1. |
| channel2= | Enables or disabled conversions on channel 2. Accepted values 0-1. |
| samples? | Reads 50 samples form the enabled channels and displays the data as pF. |
| buttons? | Checks if any of the two buttons are pressed or released. |
| reset= | Resets the device. Accepted value: 1. |
Commands can be executed using a serial terminal connected to the UART1 peripheral of dsPIC33FJ128MC706A.
The following image shows a list of commands in a serial terminal connected to processor’s UART peripheral.
Software Project Setup
This section presents the steps for developing a software application that will run on the Digilent Cerebot MC7 development board for controlling and monitoring the operation of the ADI part.
- Run the MPLAB X integrated development environment.
- Choose to create a new project.
- In the Choose Project window select Microchip Embedded category, Standalone Project and press Next.
- In the Select Device window choose dsPIC33FJ128MC706A device and press Next.
- In the Select Tool window select the desired hardware tool and press Next.
- In the Select Compiler window chose the XC16 compiler and press Next.
- In the Select Project Name and Folder window choose a name and a location for the project.
- After the project is created, the source files have to be copied in the project folder and included in the project.
- The project is ready to be built and downloaded on the development board.
More information
- Example questions:
- An error occurred while fetching this feed: http://ez.analog.com/community/feeds/allcontent/atom?community=2077
- AD5160-適用于瑞薩微控制器平臺的無操作系統驅動程序
- AD5160-適用于微芯片微控制器平臺的無操作系統驅動程序
- AD5628-適用于微芯片微控制器平臺的無操作系統驅動程序
- AD7303-適用于單片機平臺的無操作系統驅動程序
- AD7091R-適用于單片機平臺的無操作系統驅動程序
- AD5541A-適用于瑞薩微控制器平臺的無操作系統驅動程序
- AD7193-適用于單片機平臺的無操作系統驅動程序
- ADXL345-適用于單片機平臺的無操作系統驅動程序
- AD7780-適用于單片機平臺的無操作系統驅動程序
- AD5781-適用于瑞薩微控制器平臺的無操作系統驅動程序
- ADT7420-適用于單片機平臺的無操作系統驅動程序
- ADXL362-適用于單片機平臺的無操作系統驅動程序
- ADP5589-適用于單片機平臺的無操作系統驅動程序
- ADXRS453-適用于單片機平臺的無操作系統驅動程序
- AD7156-適用于瑞薩微控制器平臺的無操作系統驅動程序
- 國產RT-thread操作系統在國民技術單片機上移植 630次閱讀
- 了解和使用無操作系統和平臺驅動程序 1295次閱讀
- 51單片機操作系統開發中有什么技巧會碰到什么問題 3020次閱讀
- 單片機多任務處理方案 9656次閱讀
- 51單片機實時操作系統的基本結構與模式 5550次閱讀
- 單片機和嵌入式系統linux的區別 7090次閱讀
- 適用于測控領域的4種實時操作系統對比分析 3703次閱讀
- 淺談電腦驅動程序的工作原理 詳解電腦驅動程序意義 3w次閱讀
- 基于嵌入式Linux內核的系統設備驅動程序開發設計 1209次閱讀
- 單片機與嵌入式系統有什么區別和聯系？ 1.4w次閱讀
- 一文看懂單片機與PLC程序設計的區別 7530次閱讀
- Windows應用程序，操作系統，計算機硬件之間的相互關系 1.2w次閱讀
- 51單片機DS1302實時時鐘驅動程序 9589次閱讀
- 基于K9F5608A的MCS-51單片機驅動程序 2116次閱讀
- 基于ADC081S051與51單片機的接口電路及驅動程序 4536次閱讀
上傳資料賺積分下載排行
本周
- 1AN-1267: 使用ADSP-CM408F ADC控制器的電機控制反饋采樣時序
- 1.41MB | 3次下載 | 免費
- 2AN158 GD32VW553 Wi-Fi開發指南
- 1.51MB | 2次下載 | 免費
- 3AN148 GD32VW553射頻硬件開發指南
- 2.07MB | 1次下載 | 免費
- 4AN-1154: 采用恒定負滲漏電流優化ADF4157和ADF4158 PLL的相位噪聲和雜散性能
- 199.28KB | 次下載 | 免費
- 5AN-960: RS-485/RS-422電路實施指南
- 380.8KB | 次下載 | 免費
- 6EE-249：使用VisualDSP在ADSP-218x DSP上實現軟件疊加
- 60.02KB | 次下載 | 免費
- 7AN-1111: 使用ADuCM360/ADuCM361時的降低功耗選項
- 306.09KB | 次下載 | 免費
- 8AN-904: ADuC7028評估板參考指南
- 815.82KB | 次下載 | 免費
本月
- 1ADI高性能電源管理解決方案
- 2.43 MB | 450次下載 | 免費
- 2免費開源CC3D飛控資料（電路圖&PCB源文件、BOM、
- 5.67 MB | 138次下載 | 1 積分
- 3基于STM32單片機智能手環心率計步器體溫顯示設計
- 0.10 MB | 130次下載 | 免費
- 4使用單片機實現七人表決器的程序和仿真資料免費下載
- 2.96 MB | 44次下載 | 免費
- 5美的電磁爐維修手冊大全
- 1.56 MB | 24次下載 | 5 積分
- 6如何正確測試電源的紋波
- 0.36 MB | 18次下載 | 免費
- 7感應筆電路圖
- 0.06 MB | 10次下載 | 免費
- 8萬用表UT58A原理圖
- 0.09 MB | 9次下載 | 5 積分
總榜
- 1matlab軟件下載入口
- 未知 | 935121次下載 | 10 積分
- 2開源硬件-PMP21529.1-4 開關降壓/升壓雙向直流/直流轉換器 PCB layout 設計
- 1.48MB | 420062次下載 | 10 積分
- 3Altium DXP2002下載入口
- 未知 | 233088次下載 | 10 積分
- 4電路仿真軟件multisim 10.0免費下載
- 340992 | 191367次下載 | 10 積分
- 5十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183335次下載 | 10 積分
- 6labview8.5下載
- 未知 | 81581次下載 | 10 積分
- 7Keil工具M(jìn)DK-Arm免費下載
- 0.02 MB | 73810次下載 | 10 積分
- 8LabVIEW 8.6下載
- 未知 | 65988次下載 | 10 積分
工商網監
評論