WINCC面板的關閉/打開SV及KV柜Q1主空開的控制原理

---------------------------------------------------------

FB100中使用：

R_TRIG_Anfo_Off_Halt (CLK:="DB_ARG".On_Off.Anfo_Off_Halt);

R_TRIG_Cancel (CLK:="DB_ARG".On_Off.Cancel);

R_TRIG_Anfo_Off (CLK:="DB_ARG".On_Off.Anfo_Off);

If (R_TRIG_SK90_ZutrittAnfo.Q Or R_TRIG_K90_ZutrittAnfo.Q)

And Not xHM_K90_ZutrittAnfo And ST_BA.K90_AnfoSG = WORD#0

OR MASTER_DIAG_STAT_REG_PF Or R_TRIG_Anfo_Off_Halt.Q Then

xHM_K90_ZutrittAnfo := True; 請求進入

R_TRIG_SK90_ZutrittAnfo.Q:= False;

End_If; 請求進入

If (R_TRIG_SK6_TE.Q And xHM_K6_TE) Or (ST_BA.K6_TE And Not ST_BA.K40) Or "DB_ARG".On_Off.Quitt Or R_TRIG_Cancel.Q Then 當ON_OFF的送點ON功能激活時

xHM_K6_TE := False; 結束K6進程停止

End_If; 停止

If (R_TRIG_SK90_ZutrittAnfo.Q Or F_TRIG_K90_ZutrittAnfo.Q Or "DB_ARG".On_Off.Quitt Or R_TRIG_Cancel.Q) And xHM_K90_ZutrittAnfo And Not MASTER_DIAG_STAT_REG_PF Then

xHM_K90_ZutrittAnfo := False;

End_If;

If (R_TRIG_SK6_TE.Q Or R_TRIG_Anfo_Off.Q) And Not xHM_K6_TE Then

xHM_K6_TE := True;

R_TRIG_SK6_TE.Q := False;

End_If;

---------------------------------------------------------

FB142系統賦值

xON := SVQxK AND (KVQxK OR Cfg.X1); SV及KV柜Q1空開在接通狀態

xOFF := NOT SVQxK AND (NOT KVQxK OR Cfg.X1); SV及KV柜Q1空開在關閉狀態

Cfg.X1：控制帶不帶KV柜，不帶為1 帶為0

xS_LS := (bVisutasten = Byte#2); 控制關閉/打開按鈕。

R_Trig_S_LS(CLK := xS_LS); 觸發激活脈沖。

WINCC面板控制關閉:

IF FrgAnw AND R_Trig_S_LS.Q THEN 按鈕點了

IF xOFF AND NOT TP_MAZ.Q THEN 空開已經關閉了，而且間隔時間已經滿足

IF NOT xOff_aktiv AND NOT xON_aktiv THEN 沒有處于激活開電或關電

iSKette := 10; 去開電步驟

ELSE

iSKette := 0;

END_IF;

ELSIF xON THEN

IF NOT xOff_aktiv AND NOT xON_aktiv THEN

iSKette := 110; 去關電步驟

END_IF;

ELSE

xF_MAZ := True; 空開狀態不對故障

END_IF;

END_IF;

TP_MAZ(IN := On_Off.Qx_Off, PT := T#2m) 斷開點后的間隔時間2m

打開ON

CASE iSKette OF

10 : (*Start*)

xAnwOff := False;

xAnwOn := True; 選擇打開模式

xOn_aktiv := True; 啟動被激活

iSKette := 20;

20 : (*Kraftspeicher laden*)

TON_Timer.PT := T#2s; 激活延遲2s

xTimer := True;

SVKx := True; SVK1先保持打開

IF TON_Timer.Q THEN 時間滿足后

xTimer := False;

SVKx := False; SVK1被關閉

xQx_On := True; ON狀態被激活

iSKette := 30;

END_IF;

30 : (*Verzoegerung Einschalten*)

IF xOn THEN 檢測NOVS，KV柜Q1開關啟動狀態

xQx_On := False;

TON_Timer.PT := Tver_On; 延遲啟動時間開始

xTimer := True;

IF TON_Timer.Q THEN 時間到達

xTimer := False;

iSKette := 40;

END_IF;

END_IF;

40 : (*Quitt Zutrittsanforderung, Halt bei Taktende*)

xQuitt := True; 復位

xQuitt_5s := True;

TON_Timer.PT := T#5s; 延遲5s

xTimer := True;

iSKette := 50;

50 : (*Quitt 5s Rueckfuehrkreis und Depassivierung*)

xQuitt := False ;

IF TON_Timer.Q THEN 時間到達后

xTimer := False;

xQuitt_5s := False;

xQuitt_Usr := True;

xSteuEin := True; 啟動點激活

iSKette := 60;

END_IF;

60 : (*Quitt Usermeldungen*)

xQuitt_Usr := False;

xOn_aktiv := False; 返回初始化

iSKette := 0;

END_CASE;

關閉SVK1繼電器

CASE iSKette OF

110: (*Start*)

xAnwOn := False;

xAnwOff := True; 選擇打開模式

xOff_aktiv := True; 關閉被激活

xF_AnlBerOff := False;

iSKette := 120;

120: (*Verzoegerung Ausschalten*)

TON_Timer.PT := Tver_Off; 延遲時間激活

xTimer := True;

xErrorOffClear := False;

IF ((TON_Timer.PT - TON_Timer.ET ) < T#10s) THEN ?剩余10S停止關閉請求 ?

xAnfo_Off_Halt := True; 發出請求關閉停止

END_IF;

IF TON_Timer.Q AND On_Off.Anl_Bereit_Off THEN 延時到達關閉準備滿足

xTimer := False;

xAnfo_Off_1 := True; 前往下一步

iSKette := 140;

ELSIF TON_S_LS_Off.Q THEN

xTimer := False;

xAnfo_Off_1 := True;

iSKette := 135;

ELSIF TON_Timer.Q AND NOT On_Off.Anl_Bereit_Off THEN 時間到達，結束

關閉報錯

xTimer := False;

xAnfo_Off_1 := True;

xF_AnlBerOff := True; 發出關閉準備錯誤

iSKette := 130;

END_IF;

///////////////////////////////////////////////////////

TON_S_LS_Off.Q 的解析：

TON_S_LS_Off(IN := (xS_LS OR Sxx_Off) AND xOff_aktiv, PT := T#4s)

xS_LS： xS_LS := (bVisutasten = Byte#2) wincc按鈕一直按住

Sxx_Off：模塊外部輸入管腳，指按鈕。

按鈕信號一直被按住要超過4s

///////////////////////////////////////////////////////

On_Off.Anl_Bereit_Off 的解析：

On_Off.Anl_Off := xAnl_Off

On_Off.Anfo_Off := xON AND xAnwOff

FB200 機器人塊

_ST_ROB.E30_Anfo_Abschalt := ON_OFF.Anl_Off;

IF NOT AnwORob AND ON_OFF.Anfo_Off THEN

IF NOT _ST_ROB.A30_Abschaltung_erlaubt THEN 機器人沒有發出機器人停止

ON_OFF.Anl_Bereit_Off := False; 選擇OFF準備將被關閉

IF ON_OFF.Anfo_Off_1 THEN

xF_AAE := True;

END_IF;

END_IF;

END_IF;

機器人控制ON_OFF能否被實施完成

130: (*nicht Bereit Ausschalten 1s Cancel ausgeben*) 結束關閉指令

xAnfo_Off_1 := False;

xAnwOn := xON;

xAnwOff := xOFF;

TON_Timer.PT := t#1s;

xTimer := True;

xCancel := True;

IF TON_Timer.Q THEN

xTimer := False;

xCancel := False;

iSKette := 0;

END_IF;

135: (*Ausschalten ohne Bereit 5s Warnung ausgeben*) 等待去第150步

xAnfo_Off_1 := False;

TON_Timer.PT := t#5s;

xTimer := True;

xOff_Visu := True;

IF TON_Timer.Q THEN

xTimer := False;

xOff_Visu := False;

iSKette := 150;

END_IF;

140: (*Anlage Bereit zum Ausschalten 30s Anl_Off ausgeben*)

xAnfo_Off_1 := False;

TON_Timer.PT := t#30s;

xTimer := True;

xAnl_Off := True; 請求OFF發出

IF TON_Timer.Q THEN

xTimer := False;

xAnl_Off := False;

iSKette := 150;

END_IF;

150: (*Leistungsschalter, Medien, Licht usw. Aus*)發出控制的VSK1為1

xSteuEin := False;

xQx_Off := True;

SVKx := True; VSK1為1

iSKette := 160;

160: (*Leistungsschalter Aus*)

xQx_Off := False; 返回0步

iSKette := 0;

END_CASE;

On_Off.Cancel

FB100

R_TRIG_Cancel (CLK:="DB_ARG".On_Off.Cancel);

If (R_TRIG_SK90_ZutrittAnfo.Q Or F_TRIG_K90_ZutrittAnfo.Q Or "DB_ARG".On_Off.Quitt Or R_TRIG_Cancel.Q) And xHM_K90_ZutrittAnfo

And Not MASTER_DIAG_STAT_REG_PF Then

xHM_K90_ZutrittAnfo := False;

End_If;

If (R_TRIG_SK6_TE.Q And xHM_K6_TE) Or (ST_BA.K6_TE And Not ST_BA.K40) Or "DB_ARG".On_Off.Quitt Or R_TRIG_Cancel.Q Then

xHM_K6_TE := False;

End_If;

關閉請求進入K90和K6進程停止

----------------------------------------------------------------

On_Off.Anfo_Off := xON AND xAnwOff;

On_Off.Anfo_Off_1 := xON AND xAnfo_Off_1;

On_Off.Anfo_Off_Halt := On_Off.Anfo_Off AND xAnfo_Off_Halt;請求停止

/////////////////////////////////////////////////////

FB100

R_TRIG_Anfo_Off_Halt (CLK:="DB_ARG".On_Off.Anfo_Off_Halt);

If (R_TRIG_SK90_ZutrittAnfo.Q Or R_TRIG_K90_ZutrittAnfo.Q)

And Not xHM_K90_ZutrittAnfo And ST_BA.K90_AnfoSG = WORD#0

OR MASTER_DIAG_STAT_REG_PF Or R_TRIG_Anfo_Off_Halt.Q Then

xHM_K90_ZutrittAnfo := True;

R_TRIG_SK90_ZutrittAnfo.Q:= False;

End_If;

請求停止發出后FB100請求進入安全門發出

/////////////////////////////////////////////////////

On_Off.Qx_On := xQx_On;

On_Off.Qx_Off := xQx_Off;

On_Off.Quitt := xQuitt;

On_Off.Quitt_5s := xQuitt_5s;

On_Off.Quitt_USR := xQuitt_USR;

On_Off.STEUEIN := xON AND xSteuEin;

On_Off.On_aktiv := xOn_aktiv AND NOT On_Off.STEUEIN;

On_Off.Anl_Bereit_Off := On_Off.Anfo_Off;

On_Off.Anl_Off := xAnl_Off;

FB100中

R_TRIG_Anfo_Off (CLK:="DB_ARG".On_Off.Anfo_Off); 關閉請求

If (R_TRIG_SK90_ZutrittAnfo.Q Or R_TRIG_K90_ZutrittAnfo.Q)

And Not xHM_K90_ZutrittAnfo And ST_BA.K90_AnfoSG = WORD#0

OR MASTER_DIAG_STAT_REG_PF Or R_TRIG_Anfo_Off_Halt.Q Then

xHM_K90_ZutrittAnfo := True;

R_TRIG_SK90_ZutrittAnfo.Q:= False;

End_If;

請求關閉，F(xiàn)B100 的K90發出

On_Off.FS_Frg_Auto := F_Trig_Hupe.Q AND Mit;

On_Off.FS_LSP_Ein := (R_Trig_FS.Q OR R_Trig_LSP.Q) AND Mit;

On_Off.ErrorOffClear := NOT xF_AnlBerOff AND NOT On_Off.Anfo_Off AND NOT On_Off.Anfo_Off_1 OR Cfg.X0;

On_Off.Cancel := xCancel;

xON := SVQxK AND (KVQxK OR Cfg.X1); SV和KV柜的反饋/ 打開繼電器

xAnwOff：選擇關閉繼電器

IF ((TON_Timer.PT - TON_Timer.ET ) < T#10s) THEN ?

xAnfo_Off_Halt := True;

END_IF;