Lightning Detector,打雷告警器
關鍵字:Lightning Detector
Egor! Come quick! A storm approaches!
Here is a VLF receiver tuned to 300 kHz designed to detect the crackle of approaching lightning. A bright lamp flashes in sychrony with the lightning bolts indicating the proximity and intensity of the storm. Figure 1 shows the simple receiver which consists of a tuned amplifier driving a modified flasher circuit. The flasher is biased to not flash until a burst of RF energy, amplified by the 2N3904, is applied to the base of the 2N4403. The receiver standby current is about 350 microamps which is nothing at all to a couple of D cells, hardly denting the shelf life. Of course, the stormier it gets, the shorter the battery life.
Here is a VLF receiver tuned to 300 kHz designed to detect the crackle of approaching lightning. A bright lamp flashes in sychrony with the lightning bolts indicating the proximity and intensity of the storm. Figure 1 shows the simple receiver which consists of a tuned amplifier driving a modified flasher circuit. The flasher is biased to not flash until a burst of RF energy, amplified by the 2N3904, is applied to the base of the 2N4403. The receiver standby current is about 350 microamps which is nothing at all to a couple of D cells, hardly denting the shelf life. Of course, the stormier it gets, the shorter the battery life.
Circuit diagram
For best effect, mount the lamp in an old-fashioned holder with an extra-large colored glass lense. Or construct your own fixture with a plate of textured colored glass behind a panel painted with black-crackle paint. Watch a few old science fiction movies for other ideas.

A totally different approach is to mount the circuit in an empty glass jar with the antenna and bulb protruding through the top. (A malted-milk jar has a nice, red plastic lid which is easy to work and looks good.) Use a pin jack for the antenna. The gadget looks quite home-made but fascinating.
Boat owners may wish to replace the lamp with a 3-volt beeper to provide an early warning of approaching bad weather. Choose one of those unbreakable clear plastic jars like the large jars of coffee creamer. A little silicone rubber will seal the antenna hole in the lid of the jar. Use a longer antenna for increased sensitivity since there are few electrical noise sources on the lake.

Tune-up is simple: adjust the potentiometer until the regular flashing just stops. (Use a multi-turn trimmer.) When properly adjusted, the lamp will occasionally flash when large motors or appliances switch on and off and an approaching storm will give quite a show. Obviously, tune-up is a bit more difficult during stormy weather. Adjust the pot with no antenna if lightning is nearby. Tune an AM radio to the bottom of the dial to monitor the pulses that the lightning detector is receiving.
This lightning detector is not so sensitive that it will flash with every crackle heard on the radio but will only flash when storms are nearby. Increased sensitivity may be achieved by increasing the antenna length. The experienced experimenter may wish to add another gain stage after the first by duplicating the 2N3904 circuitry including capacitor coupling with the addition of a 47 ohm emitter resistor to reduce the gain somewhat. This additional gain can cause stability problems if the layout is poor so novices are advised to use a longer antenna or adjust the sensitivity potentiometer more delicately instead! (When operating properly, the additional gain makes the pot adjustment much less critical.)
This lightning detector is not so sensitive that it will flash with every crackle heard on the radio but will only flash when storms are nearby. Increased sensitivity may be achieved by increasing the antenna length. The experienced experimenter may wish to add another gain stage after the first by duplicating the 2N3904 circuitry including capacitor coupling with the addition of a 47 ohm emitter resistor to reduce the gain somewhat. This additional gain can cause stability problems if the layout is poor so novices are advised to use a longer antenna or adjust the sensitivity potentiometer more delicately instead! (When operating properly, the additional gain makes the pot adjustment much less critical.)
聲明:本文內容及配圖由入駐作者撰寫或者入駐合作網站授權轉載。文章觀點僅代表作者本人,不代表電子發燒友網立場。文章及其配圖僅供工程師學習之用,如有內容侵權或者其他違規問題,請聯系本站處理。
舉報投訴
發布評論請先 登錄
相關推薦
熱點推薦
FH152C6 蘋果 Lightning OTG 輸出3.3V/5V取電芯片數據手冊
FH152C6蘋果Lightning OTG輸出取電芯片
發表于 07-02 16:35
?0次下載
TECS OpenStack資源池虛機寫磁盤時延高告警的問題處理
某運營商TECS資源池,在當前告警中顯示“虛機寫磁盤時延高告警”,如下圖所示。告警統計總體平均10分鐘左右自動恢復。

排查并處理共享站點S1用戶面路徑不可用告警
共享站點S1用戶面路徑不可用告警排查處理 ? 某區域在12月14-15日開通共建共享后,運營商A部分4G基站上出現S1用戶面路徑不可用告警告警,同時E-RAB釋放次數(S1鏈路故障原因)次數增多明顯

華為云 X 實例監控與告警管理詳解
前言 隨著云計算的飛速發展,越來越多的企業將業務部署在云平臺上,云服務器實例的管理變得尤為重要。云實例的穩定性、性能及安全性,直接影響著業務的連續性與用戶體驗。為了確保這些目標的實現,監控與告警

工業智能網關可以采集什么設備數據并實現自動告警
隨著工業物聯網與數字化轉型的全面發展,工業智能網關在各行各業的應用越來越廣泛。它能夠?qū)崿F(xiàn)PLC、儀器儀表、傳感器、數控機床、工業機器人、注塑機等設備數據采集,實現5G/4G/WIFI/以太網等方式

如何借助邊緣智能網關實現廠區粉塵智能監測告警
針對工業場景中的粉塵狀況監測、管理及預警,佰馬提供基于邊緣智能網關的粉塵監測告警方案,幫助企業高效實現現場安全管理、風險防控、隱患排查、監測預警、環境保護等功能整合。

dac3171 config5的alarm_dataclk_ gone有告警是什么原因?
使用的是DAC 31717bit模式。FPGA有數據輸出,也有隨路時鐘216M。但3171的config5 的alarm_dataclk_ gone有告警。用示波器測試有時鐘216M輸入到DAC里面,DAC無輸出,請問還需要配置其它寄存器不?或者有肯是什么問題,多謝!!
發表于 12-20 07:02
卸料風機壓力檢測自動告警如何實現?有什么功能
系統的正常運行。 對此,為加強對風機的監控管理能力,卸料風機壓力檢測自動告警系統方案。通過接入風機控制器PLC以及輸送管道壓力計,能夠?qū)崟r(shí)采集風機狀態與管道壓力并實現自動告警,及時上傳到企業管理平臺中,幫助企業快
電極式傳感器不告警的原因有哪些
電極式傳感器不告警的原因可能涉及多個方面,以下是一些常見的原因及其解釋: 電極污染或損壞 : 傳感器電極可能因長期使用而污染,如被污垢、沉積物或其他雜質覆蓋,導致電極間的電導率降低,無法準確檢測液位
城市路燈水浸監測自動告警系統方案
天氣條件下,路燈設施極易遭受內澇積水影響,導致短路、損壞甚至引發觸電事故,嚴重威脅公共安全。為此,設計并實施一套高效的城市路燈水浸監測自動告警系統顯得尤為重要。 對此,數之能提供城市路燈水浸監測自動告警的物聯

CPS8849B Lightning轉USB資料分享
1.為什么需要C口型接收器到閃電適配器2.USB-C到Lightning的MFi要求3.成都易沖USB-C到Lightning解決方案4.USB-C轉照明 MFi 認證我們來看一下為什么需要
發表于 08-19 11:47
?2次下載
IR615配置流量告警方法
1.登錄路由器,服務流量管理中設置流量使用閥值.
2.添加告警設置,在服務>告警設置中勾選告警輸入和告警輸出.
3.登
發表于 07-25 07:59
EM儲能網關 ZWS智慧儲能云應用(4) — 告警介紹(下)
ZWS智慧儲能云平臺,作為一個開放式第三方平臺,是如何自定義創建告警規則的?本文將介紹儲能系統如何創建告警規則、后續如何維護。儲能系統的告警功能至關重要,它能夠確保系統的穩定與安全。云端告警

評論